Ground link
The fixed frame between the two offset pivots. Its length and inclination govern the reachable deformation range.
Technology
A planar four-bar mechanism, integrated inside a NACA 2412 section, drives a morphing trailing edge. The wing does not gain surfaces — it gains a controllable shape.
Conceptual diagram — trailing-edge morphing about a hinge line. Illustrative geometry, not published dimensions.
Section baseline
A well-documented cambered section gives the study a defensible baseline: known camber, known thickness, published aerodynamic behaviour. The mechanism then defines what the section can become.
Section characteristics
The section provides a fixed geometric baseline for synthesis. Any aerodynamic benefit of morphing it remains a research question to be quantified, not an established result.
MorphEdge X1 architecture
The mechanism is planar and entirely contained within the section. Offset pivots let the linkage work inside a thin profile without the ground link crossing the aerodynamic surface.
The fixed frame between the two offset pivots. Its length and inclination govern the reachable deformation range.
The driven input link. Small crank rotation produces a bounded, repeatable trailing-edge output.
Transmits motion between crank and rocker. Its length strongly influences transmission angle and mechanical advantage.
The output link, rigidly coupled to the morphing trailing-edge segment about the hinge line.
Vertically separated fixed pivots allow the linkage to fit inside a thin section without intersecting the surface.
The deformable segment aft of the hinge, treated as a compliant structure driven by the rocker.
Central objective
The mechanism is not useful unless its output can be predicted. The programme therefore treats the linkage as a function generator: for a given crank input, the trailing-edge rotation must follow a defined law that can be synthesised, analysed and later measured.
The law is the deliverable. Everything downstream — stiffness, mass, actuator sizing, aerodynamic consequence — depends on how well it can be realised.
Theory of Machines — methods applied
Confirm the degree of freedom of the planar mechanism before synthesis begins.
Classify linkage behaviour and understand which links can rotate fully.
Relate link lengths to input and output angles for function generation.
Solve vector loop equations for position at every input angle.
Full kinematic solution across the working range of the mechanism.
Keep the coupler–rocker angle away from singular configurations where force transfer collapses.
Estimating how input torque maps to trailing-edge actuation effort.
Identify configurations where the linkage locks or loses controllability.
Approximate the target deformation law over an interval with minimised error.
Translate aerodynamic and structural resistance into required input effort.
Aerodynamics
Morphing changes geometry; these are the quantities that determine whether the change is aerodynamically meaningful.
Lift
L = ½ ρ V² S C_L
Trailing-edge camber change alters the lift coefficient at a given attitude.
Drag
D = ½ ρ V² S C_D
Parasite and induced contributions are treated separately in the study.
Aspect ratio
AR = b² / S
Links planform choice to induced-drag behaviour in the baselines.
Reynolds number
Re = ρ V c / μ
Sets the flow regime for the UAV-scale sections under study.
Induced drag
C_Di = C_L² / (π e AR)
Efficiency factor e is treated as an unknown until measured.
The single number that decides whether a morphing wing earns its mass.
Camber change shifts the moment balance; trimming authority must follow.
The realised deformation law defines the achievable camber schedule.
A segmented trailing edge must resist aerodynamic load without unacceptable deflection.
Input torque versus useful aerodynamic change — measured, not assumed.
Repeatability and tolerance sensitivity under real manufacturing limits.
No numerical performance results are published at this stage. Values will be reported only after computational study and experimental validation.
Potential applications
These are application targets used to frame the research, not capabilities the programme claims today.
Long-loiter platforms where a wider efficient lift range reduces the need for discrete high-lift hardware.
Slow, sensor-carrying aircraft operating across varying payload and altitude conditions.
Repeated low-speed survey passes where trim efficiency directly affects sortie duration.
Close-proximity flight profiles that benefit from low-speed control authority.
Smooth, continuous camber change as an alternative to hinged control surfaces.