Requirements
Define morphing objectives, flight envelope, constraints and acceptance criteria.
Research & Development
The programme is built as a sequence of answerable questions, each with a defined method and a defined failure mode.
Central research question
Conceptual schematic — the mechanism as a function generator.
Research workflow
The sequence runs from requirements to validation. Theory precedes computation, and computation precedes hardware — no stage is skipped.
Define morphing objectives, flight envelope, constraints and acceptance criteria.
Establish the NACA 2412 reference section and candidate UAV baseline planforms.
Synthesise a four-bar for the target trailing-edge deformation law.
Solve position, velocity and acceleration; check transmission angle and singularities.
Package the linkage inside the section and integrate the morphing trailing edge.
Evaluate aerodynamic behaviour and structural response of the concept.
Refine link geometry, stiffness and actuation effort within constraints.
Manufacture the demonstrator with conventional workshop processes.
Kinematic bench, static structural loading and aerodynamic demonstration.
Compare measured behaviour against simulation and document uncertainty.
Current position: stage 03 — mechanism synthesis and kinematic analysis. Stages 05 to 10 are planned work packages, not completed results.
Preliminary research
Two AERY32 baseline configurations were explored to understand what the mechanism must fit into. They are separate baseline designs studied side by side — not the same wing in different morphing positions.
Configuration A
A moderately swept baseline favouring induced-drag efficiency at cruise. Longer span means greater structural loading at the root and less spare volume for mechanism packaging.
Configuration B
A shorter-span baseline suited to preliminary mechanism integration at low speed. Easier packaging and lower root loads, with a different induced-drag penalty to weigh.
Trade-offs under study
Exploratory kinematics
Exploratory four-bar studies examined offset pivots, alternative actuation arrangements, rocker motion and the trajectories traced through the working range.
What the studies examined
These are exploratory simulations. Link dimensions, pivot coordinates and actuator placement are not published at this stage.
Tools in the programme
Fabrication
The initial hardware prioritises visible motion, repeatability, access and measurement. Flight readiness is explicitly out of scope for the first build — a demonstrator that can be measured is worth more than one that can only be photographed.
Processes available to the programme are conventional workshop processes, chosen for tolerance realism rather than novelty.
Flat link plates and fixture plates with repeatable edges.
Forming and blanking where a press is more practical than machining.
Repeatable sheet bends for brackets and mounting frames.
Complex link housings and prototype trailing-edge segments.
Pivot bores, shafts and any interface needing tight tolerance.
Planned experimental validation
Validation is planned, not performed. Each test is designed to answer a question the simulations cannot.
Measure input angle against trailing-edge rotation on a rigid bench fixture. Establishes whether the realised mechanism follows the synthesised law.
Apply representative loads to the morphing segment and observe deflection and stiffness. Identifies whether the structure survives before any flow is introduced.
Introduce flow and measure whether deformation produces measurable, repeatable change. The most demanding stage and the last in the plan.
Instrument resolution, fixture compliance and alignment error are recorded with every result.
Repeated sweeps establish whether the deformation law is stable or hysteresis-dominated.
Measured behaviour is compared against the kinematic model, and differences are explained rather than smoothed over.
Research roadmap
Statuses describe where each package stands. There are no invented progress percentages and no promised completion dates.
Intellectual property evaluation and commercialisation feasibility are long-term objectives, not current activity.
Research formulation and literature review
Aerodynamic baseline and CAD modeling
Mechanism synthesis and kinematic analysis
Integrated mechanism and wing optimization
CFD and structural simulation
Physical demonstrator fabrication
Experimental aerodynamic validation
Intellectual property evaluation and commercialization feasibility
Preliminary study
The October 2026 preliminary investigation brings together MechSim mechanism models, synchronized point-motion exports and derived kinematic analysis.
Screen recordings document mechanism motion and data collection. Public captures are available in the media gallery.
The analysis workflow examines point trajectories, speed, acceleration, input–output rotation and transmission angle. The current geometry is provisional.
Mechanism synthesis must connect a specified deformation requirement to packaging, actuation and structural constraints before aerodynamic benefit can be evaluated.
Reports, proposal slides, raw datasets and mechanism models remain private. Numerical simulation outputs are not validated flight results or actuator design loads.
View the original recordings